A Step-by-Step Guide to Setting Up a Bathtub
A Step-by-Step Guide to Setting Up a Bathtub
Blog Article
Here in the next paragraph you'll find a bunch of awesome material related to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately hard job. If the old tub is easily easily accessible, the job can relocate immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have certified yourself for the task and fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is far better to think about using one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will assist you mount a new bath tub in your bathroom if you have currently bought a brand-new bathtub and don't require to change the plan of your previous water pipes.
Your tools and also material checklist must consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing the two wood boards under its feet, position the tub in the required setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
Switch on the water system as well as examine all joints and also new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub must wait till the bath tub has actually been made use of at least once as this will settle it into its final setting.
Getting ready for the Setup
First of all, the sustaining framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing issues with dampness and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the activity experienced when the tub remains in usage. The sealer can crack rather early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very serious about How to Install a Bathtub and I hope you appreciated the blog entry. Feel free to take a moment to share this entry if you liked it. Thanks a lot for your time. Please come visit our site back soon.
Detail
Report this page